Deluxe Round Shallow Escutcheons (Flanges)
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
3/8"
IPS Deluxe Shallow Escutcheons:
Escutcheon inside diameter: 5/8"
1/2"
IPS Deluxe Shallow Escutcheons:
Escutcheon inside diameter: 13/16"
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
5/8"
OD Deluxe Shallow Escutcheons:
Escutcheon inside diameter: 5/8"
1-1/4"
OD Deluxe Shallow Escutcheons:
Escutcheon inside diameter: 1-1/4"
1-1/2"
OD Deluxe Shallow Escutcheons:
Escutcheon inside diameter: 1-1/2"
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
↓
IPS Round Shallow Escutcheons
↓
OD Round Shallow Escutcheons
Plastic White Shallow Escutcheons
Corrosion proof
High density polyethylene - virtually indestructible
↓
IPS Round Shallow Escutcheons
↓
OD Round Shallow Escutcheons
Stylish Deluxe Shower Arm Escutcheons with Set Screw
overall outside diameter: 2-3/4"
escutcheon inside diameter: 7/8"
Designed specifically for shower arms
shower arms are typically thinner wall (smaller outside diameter) than normal pipe nipples
Deluxe Shower Arm Escutcheon
with Set Screw - 1/2" MIPT:
Please note: Polished Brass model is slightly different than Chrome & Satin Nickel models
This extra wide escutcheon features:
- Fits 1/2" IPS wall and ceiling drop nipples
- View detailed dimensions
- Heavy brass construction
- Will fit brass, galvanized, black, stainless and other iron pipe size stub out nipples
- Available in a variety of designer finishes
- Shown in chrome
Measure the outside diameter of your pipe and compare to the escutcheon inside diameter
Designer Extra Wide Heavy Brass Escutcheons:
Extra Wide Sure Grip
Chrome Escutcheons
(Flanges)
Measure the outside diameter of your pipe and compare to the escutcheon inside diameter
Designer Heavy Brass Escutcheons with O-Ring
overall outside diameter: 2-1/4"
escutcheon inside diameter: 13/16"
This heavy duty escutcheon features:
Measure the outside diameter of your pipe and compare to the escutcheon inside diameter
Designer Heavy Brass
Escutcheon with O-Ring:
Deluxe Bell Escutcheons
Measure the outside diameter of your pipe or cover tube and compare to the Escutcheon Inside Diameter
3/8"
IPS Deluxe Bell Escutcheons:
Escutcheon inside diameter: 5/8"
1/2"
IPS Deluxe Bell Escutcheons:
Escutcheon inside diameter 7/8"
Measure the outside diameter of your pipe or cover tube and compare to the Escutcheon Inside Diameter
11/16"
OD Deluxe Bell Escutcheons:
Escutcheon inside diameter 11/16"
5/8"
OD Deluxe Bell Escutcheons:
Escutcheon inside diameter 5/8"Trying to find a bell escutcheon for a 5/8" copper cover tube? Use the 11/16" flange above
Chrome Plated Bell Escutcheons
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
Deluxe Round Box Escutcheons
(for P-Traps)
Measure the outside diameter of your pipe or p-trap and compare to the escutcheon inside diameter
Antique Brass
1-1/4" OD -
view dims1-1/4" escutcheon inside diameter
Matte Black
1-1/2" OD -
view dims1-1/2" escutcheon inside diameter
1-1/4" OD Deluxe Round Box Escutcheon for 1-1/4" P-Traps:
1-1/2" OD Deluxe Round Box Escutcheon for 1-1/2" P-Traps:
Chrome Plated Round Box Escutcheons
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
↓
IPS Round Box Escutcheons
↓
OD Round Box Escutcheons
Heavy Gauge Chrome Plated Steel Escutcheons with Springs
Snap/Split - Retro Fit
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
These Snap/Split escutcheons have springs because they will not always fit snugly on every type of pipe
Please note: All dimensions are approximate
↓
IPS Two-Piece Escutcheons
↓
OD Two-Piece Escutcheons
Order in quantities of 24, 48, or 96
for even greater savings!
Two-Piece Chrome Plated Light Gauge Steel Escutcheons
Measure the outside diameter of your pipe and compare to the Escutcheon Inside Diameter
↓
IPS Two-Piece Escutcheons
↓
OD Two-Piece Escutcheons
Order in quantities of 24, 48, or 96
for even greater savings!
Standard Ceiling Mount Drop Nipples
Available in quality standard finishes -
Ideal for ceiling mounted rainshower heads
Deluxe Brass Constructed Nipples
Available in many designer finishes -
Ideal for ceiling mounted rainshower heads
Brass Constructed 1/2"
IPS x 4" Ceiling Mount Drop Nipple:
Brass Constructed 1/2"
IPS x 6" Ceiling Mount Drop Nipple:
Brass Constructed 1/2"
IPS x 12" Ceiling Mount Drop Nipple:
Self Seal Tub Spout & Shower Arm
Trim Plates
- Fits 1/2" copper and 1/2" & 3/4" galvanized pipe nipples
- Provides water leak protection in two areas: between spout plate and wall and around pipe protruding from wall
- Covers unsightly stains or marks from prior installation
- Quick and easy installation
- Approximate dimensions: 3-1/4" O.D. ; 1-1/2" I.D. (max) and 3/8" thick
- This side view gives you a better look at the elevation and ridge pattern of these shower arm trim plates
Please Note: The foam rings included with these trim plates are intended to stretch over the pipe to provide a snug, leak-protected fit. Please do not attempt to cut the foam ring, as this may compromise its ability to perform that function.
DrySeal™ Pipe Collar for Tub Spouts & Shower Arms
No special tools required
Tapered design compresses tightly to wall.
Creates a watertight seal around the pipe or tubing
Helps eliminate moisture creeping into wall opening, helping to prevent mold growth
Tub Spout Cover Up
No special tools required - Great for rental properties
Tub Spout Cover Up -
Fits Standard Tub Spouts = $9.69
3-1/2"OD; 1 3/4"ID; 1/8" thick;
chrome / mirror acrylic finish
IPS & OD Pipe Sizing Explained
"IPS" stands for "Iron Pipe Size". Galvanized, black, stainless steel, brass, PVC and ABS schedule 40 are iron pipe sized piping. IPS pipe sizes are denoted by the inside diameter of the pipes, which are not precise measurements. The outside diameter of the pipe itself must be measured for correct size identification, as listed on the chart below. Once the pipe size is determined, choosing the correct escutcheon is easy since IPS escutcheons are designated by the IPS pipe size they will fit. Read further detailed information about IPS pipe sizing.
"OD" stands for "Outer Diameter" and is a measurement of the diameter of the pipe as taken from the outside edge to outside edge of the pipe looking straight at the body (not the threads) of the pipe. Copper piping is easier to determine by the outside diameter than IPS piping.
Standard IPS Nipple and Pipe Sizing
Pipe
Size |
Approximate
Outside Diameter (O.D.) |
Approximate
Circumference |
| 1/8" |
3/8" |
1-1/4" |
| 1/4" |
1/2" |
1-3/4" |
| 3/8" |
5/8" |
2-1/8" |
| 1/2" |
7/8" |
2-5/8" |
| 3/4" |
1-1/16" |
3-5/16" |
| 1" |
1-1/4" |
4-1/8" |
| 1-1/4" |
1-5/8" |
5-1/4" |
| 1-1/2" |
1-7/8" |
6" |
| 2" |
2-3/8" |
7-7/16" |
| 2-1/2" |
2-7/8" |
9-1/16" |
| 3" |
3-1/2" |
11" |
| 4" |
4-1/2" |
14-1/8" |
| 5" |
5-9/16" |
17-1/2" |
| 6" |
6-5/8" |
20-3/4" |
| 8" |
8-5/8" |
27-1/8" |
| 10" |
10-3/4" |
33-3/4" |
| 12" |
12-3/4" |
40-1/16" |
Circumference = distance measured around the outside of the pipe
Round Shallow Escutcheon
Outside Dimensions
Escutcheon
Pipe Size |
Escutcheon
O.D. Size |
| 3/8" IPS |
2-1/2" O.D. |
| 1/2" IPS |
2-1/2" O.D. |
| 3/4" IPS |
2-1/2" O.D. |
| 1" IPS |
2-3/4" O.D. |
| 1-1/4" IPS |
2-7/8" O.D. |
| 1-1/2" IPS |
3" O.D. |
| 2" IPS |
3-1/2" O.D. |
Escutcheon
Pipe Size |
Escutcheon
O.D. Size |
| 1/2" OD |
2-1/2" O.D. |
| 5/8" OD |
2-1/2" O.D. |
| 7/8" OD |
2-1/2" O.D. |
| 1-1/8" OD |
2-1/2" O.D. |
| 1-1/4" OD |
2-3/4" O.D. |
| 1-3/8" OD |
2-3/4" O.D. |
| 1-1/2" OD |
2-7/8" O.D. |
| 1-5/8" OD |
2-7/8" O.D. |
| 2" OD |
3-1/2" O.D. |
Example:
Purchase Round Shallow Escutcheons
Frequently Asked Questions
Q. "What is the purpose of a pipe escutcheon?"
A. Think of pipe escutcheons as multipurpose trim for your plumbing setup. They're like protective and decorative sleeves for where your pipes poke through walls or floors, covering up any gaps or rough edges while also making your plumbing look neat and polished. Plus, they shield against water and debris sneaking past where it shouldn't, helping to prevent damage. Basically, they enhance the appearance of plumbing installations while offering protection against potential damage.
Q. "How are escutcheons kept in place?"
A. The pipe itself keeps the escutcheon centered; you can seal the underside of the rim with caulk or adhesive, which will block seepage and keep secure the escutcheon to the wall or floor.
Q. "What are snap/split escutcheons used for?"
A. Snap/split escutcheons are perfect for quick and easy installation around existing pipes without the need for disassembly. They are designed to separate at one end and have a hinge on the other side, which allows them to be spread apart on one side and then be closed in place around the pipe without having to slide them over an open end of the pipe. This makes them particularly useful for retrofitting or repairing plumbing installations where pipes are already in place.
Q. "What is a Smitty plate used for?"
A. A Smitty plate (also known as a remodeler's plate or a repair or retrofit plate) is used to cover larger holes in the wall where a faucet valve may have been replaced and it is not cost effective to replace the whole wall. They are also used when a larger hole was needed to repair a valve or leak, and a regular escutcheon is not sufficient to cover it.
Q. "What does "PVD" polished brass mean?"
A. "PVD" stands for "Physical Vapor Deposition" which is a modern plating process used in faucet manufacturing. Vaporized zirconium reacts with nitrogen and other gases to form a VERY durable plated surface. Unlike polished brass finishes in the past that would easily tarnish over time, polished brass finishes with PVD are extremely durable and won't generally tarnish or discolor.
